Nady Systems UIC80PP User Manual download pdf (Page 9)

Installing Antennas

Install antennas by connecting the two

Antennas (19) included with your system to

the two RF Connectors (18) located on the

back of your W-1KU receiver. The optimal

positions of the antennas are 45 degrees

from the receiver and 90 degrees from each

other. For maximum range, it is always best

to maintain a line-of-sight (no obstructions)

between the receiver antennas and the

transmitter at all times whenever possible.

Powering the Receiver

To power the receiver, plug the provided

AC/DC Power Supply (14) adapter into the

DC Input Jack (13) on the back of the receiver,

then plug the adapter into an AC outlet.

Note: Any 15-18VDC source with minimum

400mA capacity can also be used.

Connect either the 1⁄4” Unbalanced Line

Out (17) or XLR Balanced Mic Out (15) to

your mixing board, effect, or ampliﬁer

(see Connecting the Audio Equipment).

To turn on, press the Power Button (12)

for two seconds. The LCD Display (2) will

light (showing Group, Channel, RF Level

Meter, Diversity, and Output Volume). The

5-segment AF LED Tree (1) will display the

received audio level when the transmitter is

activated and audio transmitted. To turn off,

press the Power button for three seconds

and release. The receiver will turn off.

Adjusting the Squelch

The RF Squelch (16) simultaneously controls

both of the A and B True Diversity receiver

mute sections. The control should be

adjusted counterclockwise to the minimum

RF squelch setting at which the RF Level

Meter (7) and the Diversity Indicator (3) will

remain on while your transmitter is in

normal use, up to the maximum operating

range anticipated in use for your application.

However, in areas of high RF activity, the

squelch control may need to be adjusted

clockwise. If the transmitter is off and the

receiver signal and the diversity indicators

are ﬂickering or stay on continuously, the

squelch should be adjusted to a higher

level (clockwise for less mute sensitivity

level) to stop the ﬂickering. Be careful

not to select too high a clockwise setting

as this may reduce the operating range

to below what is needed. A range walk

test will help in selecting the proper level.

If the range is not critical, note that a

clockwise (maximum squelch) setting will

also yield a quieter mute function, which

might be desired in certain applications.

The squelch level is factory preset at

maximum sensitivity and operating range

(i.e. counterclockwise for minimum squelch

level—maximum usable range).

Audio Level and Peak LED Indicator

The W-1KU receiver has a 5-segment

AF Level LED Display (1) that lights up

sequentially, indicating the level of the audio

signal from the transmitter. Occasional

ﬂickering of the top (red) Peak LED on loud

inputs to the transmitter is normal. If the

Peak LED lights continuously decrease

the input audio level to the transmitter

or overload distortion may result.

Connecting the Audio Output

The W-1KU audio output is set up for either

balanced mic (ﬁxed level) or unbalanced line

(adjustable level). The Unbalanced Line Out

is controlled by the or volume control

buttons. The receiver Volume Display (6) will

indicate the level selected. For balanced

output, plug an audio cable with an XLR

connector into the XLR Balanced Mic Out (15)

socket and plug the other end into your

mixing board or ampliﬁer. For unbalanced

output, plug an audio cable with a 1⁄4”

mono (Tip/Sleeve) plug into the Unbalanced

Line Out (17) jack and plug the other end into

your mixing board or ampliﬁer. When using

the BT-1KU instrument transmitter system,

connect the Unbalanced Line Out directly

to your instrument amp or preamp.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Comments to this Manuals

No comments

Nady Systems UIC80PP User Manual Page 9

Comments to this Manuals

Related products and manuals for Guitar accessories Nady Systems UIC80PP